|
Product Details:
Contact Now
Chat Now
|
| Power: | 1W | Customization: | Available |
|---|---|---|---|
| Resistance: | Fixed Resistor | Function For Resistance: | Protective Resistor, Load Resistor |
| Model NO.: | 1W3*10 | Installation: | DIP Resistor |
| Transport Package: | Carton | Tolerances: | 5% 10% |
| Ambient Temperature: | -55 ° C + 125 ° C | ||
| Highlight: | 1W Metal Oxide Film Resistor,0r36 Nonflammable Resistor,0r99 Nonflammable Resistor |
||
1W3*10 Mof 0r36-0r99 0r Taping Type Metal Oxide Film Resistor
Product Details
Our metal oxide film resistors offer stable performance, reliable tolerance, and excellent cost efficiency, making them ideal for general-purpose electronic circuits. Constructed on a high-quality ceramic core with a metal oxide film coating, these resistors provide good heat resistance and long-term stability
Introduction
| 1. The resistance value change ratebetween pre-and-post test shall be within ±5%. | |
| 2. Power ratings: 1/6W, 1/4W, 1/2W, 1W, 1W3*10, 1W3.5*10, 2W, 3W, 5W | |
| 3. Tolerance: ±5% standard | |
| 4. Resistance range: 0.1Ω ~ 120KΩ |
Product mix
| NO. | Material name | Material |
| 1 | Lead wire | Tinned copper wire or tinned copper-clad steel,without lead |
| 2 | End cap | Tinned iron |
| 3 | Carbon film | The conductive film is a metal oxide film |
| 4 | Ceramic rod | High-aluminum content ceramics |
| 5 | Colour code | Silicone resin coating |
| 6 | Finish paint | Non-combustible resin |
| Style | Max Working | Max Overload | Dielectric Withstanding V | Resistance Value Range |
| 1/6W.1/8W.1/16W | 200V | 400V | 200 | 0.1Ω~120KΩ |
| I/4 W / 1/4WS | 250V | 500V | 250 | 0.1Ω~120KΩ |
| 1/2W / 1/2WS | 350V | 700V | 350 | 0.1Ω~120KΩ |
| 1W / 1WS | 350V | 700V | 350 | 0.1Ω~120KΩ |
| 2W /2WS | 350V | 700V | 500 | 0.1Ω~120KΩ |
| 3W / 3WS | 500V | 1000V | 500 | 0.1Ω~120KΩ |
| 5W / 7WS | 600V | 1000V | 700 | 0.1Ω~120KΩ |
Solder-ability
The leads with flux are dipped in a melted solder of 235 ±5°c for 2 seconds,more than 95% of the circumference of the lead wires shall be covered with solder.
Resistance to Soldering Heat
Two leads are together dipped in a melted solder of 270 ±5°c for 10 ±1seconds, or 350±10°c for 3.5 ±0.5 seconds, Then remove the resistorsand leaving them at room temp. for one hour. The resistance value change rate between pre-and-post test shall be within ±1%.
Nonflammability
The resistors are applied the power of 16 times the rated wattage for 5 min. and shallnot get flame.
Contact Person: Mr. Jim
Tel: 15361036926