|
Product Details:
Contact Now
Chat Now
|
| Power: | 5W | Type: | Metal Oxide Film Resistor |
|---|---|---|---|
| Application: | Medical Apparatus And Instruments | Resistance Range: | 0.1r~22mr |
| Rated Temperature Rise: | 375 ° C | Packaging: | Throught Hole |
| Transport Package: | Carton | Tolerances: | 5% 10% |
| Ambient Temperature: | -55 ° C + 125 ° C | ||
| Highlight: | Anti Corrosion Metal Film Resistor,Metal Film Resistor 10k Ohm,Small 10k Ohm 5 Watt Resistor |
||
Metal Oxide Film Resistor 10K Ohm 5W 5% Color Code Resistor
Product Details
Stable performance, extensive resistance, small size,high operating temperature and high ultimate voltage. adopt vacuum evaporation sputtering nickel-chromium alloy film on high-purity ceramic substrate, laser fine trimming to lock precise resistance value. Smooth blue epoxy protective coating, anti-corrosion, moisture resistance, effectively prevent film aging during long-term operation, much better stability than carbon film resistors.
Introduction
| 1. Power:0.125W~5W | |
| 2. Resistance tolerance:±2% ±5% ±10% | |
| 3. Operating ambient temperature: -55ºC~ +125ºC | |
| 4. The resistor's normal size coats yellow and the mini size coats brown |
Product mix
| NO. | Material name | Material |
| 1 | Lead wire | Tinned copper wire or tinned copper-clad steel,without lead |
| 2 | End cap | Tinned iron |
| 3 | Carbon film | The conductive film is a metal oxide film |
| 4 | Ceramic rod | High-aluminum content ceramics |
| 5 | Colour code | Silicone resin coating |
| 6 | Finish paint | Non-combustible resin |
| Watts | L | D | H | d±0.05mm |
| 1/6W/1/8W/1/16W | 3.3±0.3 | 1.8±0.3 | 28.0±2.0 | 0.33 |
| 1/4WS | ||||
| 1/4W | 6.0±0.5 | 2.3±0.3 | 27.0±2.0 | 0.33 |
| 1/2WS | ||||
| 1/2W | 9.0±0.5 | 3.2±0.3 | 26.0±2.0 | 0.40 |
| 1WS | ||||
| 1W | 11.0±1.0 | 4.5±0.5 | 35.0±2.0 | 0.45 |
| 2WS | ||||
| 2W | 15.0±1.0 | 5.0±0.5 | 33.0±2.0 | 0.50 |
| 3WS | ||||
| 3W |
17.0±1.0 |
6.0±0.5 | 32.0±2.0 | 0.60 |
| 5WS | ||||
| 5W |
24.0±1.0 |
8.0±1.0 | 28.0±2.0 | 0.70 |
Moisture-proof Load Life
The resistors arrayed are placed into a constant temp./humidity oven at the temp. of 40±2°c and the humidity of 90~95%, then rated power is applied for 1.5 hours and cut off for 0.5 hour. The similar cycle will be repeated for 500+24 -0 hours in total (including cut-off time). Then remove the voltage, taking the resistors out of the oven and leaving them at room temp. for one hour. The resistance value change ratebetween pre-and-post test shall be within ±5%. There also shall be no evidence of remarkablechange on appearance,and the markingshall not be illegible.operating ambient temperature: -55ºC~ +125ºC.the resistor's normal size coats yellow and the mini size coats brown.
Contact Person: Mr. Jim
Tel: 15361036926