Home Cases

Metal Oxide Film Resistor Case Study: Flameproof 1/2W-5W Solution for EV Charging Station Power Modules

Certification
China Shenzhen Enhuida Electronics Co., Ltd certification
China Shenzhen Enhuida Electronics Co., Ltd certification
I'm Online Chat Now

Metal Oxide Film Resistor Case Study: Flameproof 1/2W-5W Solution for EV Charging Station Power Modules

November 18, 2026
Latest company case about Metal Oxide Film Resistor Case Study: Flameproof 1/2W-5W Solution for EV Charging Station Power Modules

Project Background

A European manufacturer of AC and DC electric vehicle charging stations needed to replace the through-hole resistors used in the surge protection, bleeder and current-sensing sections of its 7 kW to 120 kW power modules. Field returns from installations in coastal and high-humidity regions showed resistance drift beyond 3% after 18 months, together with cracked coating on resistors mounted close to the AC/DC heat sink. The customer required a flameproof, heat-resistant fixed resistor that could survive -40°C winter starts and 85°C internal cabinet temperatures while keeping 5% tolerance and remaining cost competitive against their existing supplier in Southeast Asia.

Requirement Analysis

Our engineering team reviewed the failing positions and mapped every circuit to a specific product family from the Metal Oxide Film Resistor range:

  • Bleeder and discharge circuits: 1/2W 220K ±5% T52 braid, requiring high working voltage and stable performance under continuous DC load
  • Inrush limiting: 3W axial metal oxide film fixed resistor, 0R33 to 0R99, needing strong resistance to instantaneous pulse current
  • Snubber and damping: 2W to 5W high power resistors, 10R to 1MR, requiring low inductance and high load capacity
  • Gate drive and sensing: 1/4W to 1W units with ±100 ppm/°C temperature coefficient

Technical Solution

The selected construction uses a high-alumina ceramic rod, a metal oxide film deposited on the core, tinned copper-clad steel lead wire without lead content, a tinned iron end cap and a non-combustible resin finish coat rated UL 94V-0. Key parameters agreed for the project:

Parameter Specification
Power rating 0.125W to 5W
Resistance range 1Ω to 1MΩ (5W: 12Ω to 500KΩ)
Tolerance ±5% (custom ±2% available)
Operating temperature -55°C to +155°C
Temperature coefficient ±100 ppm/°C
Working voltage Up to 800V
Dielectric withstanding voltage 250V to 1000V
Flammability UL 94V-0 flame-retardant coating
Certification CE, RoHS

Validation and Test Results

Samples were validated against the customer's incoming inspection protocol, which follows IEC 60115 test conditions: 20±2°C ambient temperature, and 10 to 35°C with 45% to 85% relative humidity for workshop testing. Short time overload was applied at 2.5 times rated voltage for 5 seconds, with resistance measured after 30 minutes of rest. The permitted drift was ±1.00% plus 0.05Ω; the delivered lots measured a maximum drift of 0.42%.

  1. 1000-hour damp heat test at 60°C / 90% RH: average drift 0.6%, no coating cracks
  2. 500 thermal cycles from -40°C to +125°C: zero open circuits, no end-cap separation
  3. Pulse surge test at 2.5x rated voltage: no flame, no visible damage
  4. Solderability and lead-free reflow compatibility: pass on first submission

Commercial Outcome

Mass production started with an initial order of 1.2 million pieces, split across seven resistance values, packed in T52 braid reels for the customer's axial insertion line. Production capacity of 200 million pieces per month allowed the full order to ship in 5 to 7 working days per batch, with T/T payment terms and EXW/FOB/CIF options. Twelve months after switching, the customer reported a 92% reduction in resistor-related field returns, no coating failures, and a landed cost 6% below the previous supplier once rework and warranty costs were included. The cooperation was extended to the next-generation 240 kW platform, where the same metal oxide film family now covers bleeder, snubber and inrush positions.

Why This Matters for Design Engineers

Metal oxide film resistors outperform carbon film parts in exactly the conditions that cause field failures: continuous heat, humidity and repetitive pulse stress. For charging stations, meters, inverters and photovoltaic systems, specifying a flameproof metal oxide film fixed resistor with documented temperature coefficient, dielectric strength and overload behaviour removes the most common warranty risk at a marginal unit cost difference.

Contact Details
Shenzhen Enhuida Electronics Co., Ltd

Contact Person: Mr. Jim

Tel: 15361036926

Send your inquiry directly to us (0 / 3000)